Electrical Tools

The Forged Crimper with Wire Stripper/Cutter combines the most commonly used wire stripping sizes with a dedicated crimper and two cutters. Strips ...

Klein's forged Wire Stripper / Cutter / Crimper Heavy-Duty Multi Tool is built with the durability of pliers, the sharpness and precision of a wire...

OPTIMIZED CIRCUIT IDENTIFICATION EFFICIENCYMapping out a complex electrical grid in a commercial or industrial facility requires more than a simple...

DUAL-SENSOR DIAGNOSTIC SUPREMACYWhen you are deep in a commercial HVAC commission or a high-density panel layout, efficiency is dictated by the qua...

ADVANCED CIRCUIT DIAGNOSTIC PRECISIONWhen you are cycling through hundreds of receptacles on a commercial build, you do not just need a go/no-go li...

RAPID CIRCUIT DIAGNOSTIC PRECISIONFor the industrial electrician, verifying circuit integrity across a high-volume facility isn't just a safety pro...

COMMERCIAL PANEL TRACING DOMINANCEWhen you're staring at an unlabeled 42-circuit panel in a high-rise commercial build, guessing isn't an option. T...

DUAL-SPECTRUM SIGNAL DIAGNOSTICSIn the world of industrial maintenance and low-voltage integration, accuracy is the difference between a successful...

HIGH-VOLUME TERMINATION PRECISIONIn the world of high-voltage industrial installations, speed means nothing without the precision required for NEC ...

PRECISION CONDUIT GEOMETRY DOMINANCEWhen you're running extensive racks and every degree matters for strict NEC compliance, a sloppy bender is a li...

RAPID TRAPEZE INSTALLATION EFFICIENCYFor the industrial electrician managing massive conduit runs, the Milwaukee 2872-21 represents a massive leap ...

PRECISION THREADED FASTENING EFFICIENCYEngineered for the high-volume mechanical and electrical contractor, the Milwaukee 2872-20 M18 Brushless Thr...

ULTRA-CLEAN DATA TERMINATION EFFICIENCYIn the world of high-volume data infrastructure, a single bad crimp can lead to hours of troubleshooting and...

MAXIMUM PRECISION DATA TERMINATIONIn the world of high-bandwidth infrastructure and complex telecommunications, your termination quality dictates y...

BURR-FREE ARMOR PENETRATIONIn high-volume electrical rough-ins, speed is useless if you're compromising conductor integrity or wasting time filing ...

MAXIMUM DATA TERMINATION PRECISIONIn the world of high-speed data networking, a single bad crimp can compromise an entire rack's certification. The...

MAXIMUM DATA TERMINATION VERSATILITYEngineered for the rigorous demands of structured cabling and data center environments, the Milwaukee 48-22-290...

ULTIMATE DATA TERMINATION PRECISIONWhen you're facing a high-density server room or a complex commercial cross-connect, the speed and reliability o...

RAPID ARMOR TERMINATION EFFICIENCYWhen your commercial production schedule demands hundreds of MC cable terminations per shift, you cannot afford t...

Klein Tools Conduit Bender Head is designed to handle thin wall EMT up to 1-1/4-Inch and rigid IMC up to 1-Inch thick. Made from Iron with Klein's ...

1 NPT tap size fits 1 in (25 mm) bender heads. Replacement handle for Cat. No. 56205. Bright orange color is easy to spot on the jobsite. Includes ...

3/4 NPT tap size fits 1/2-Inch (13 mm) and 3/4-Inch (19 mm) bender heads. Made from high-strength steel to eliminate flex and provide excellent fee...

The innovative new Double-S Hook is a replacement part for the 7-Piece Fish Rod Attachment Set. Rotate the hook clockwise to grab then secure wires...

Klein Tools offers an innovative variety of durable attachments providing the right tool for any wire and cable fishing situation. This seven-piece...

Keep these replacement leaders handy when wire pulling with fiberglass fish tapes. They are good to have around just in case anything unexpected ha...

Easily locate fish rod end in dark spaces. The illuminated fish rod tip from Klein Tools lights up for maximum visibility. You'll enjoy long life f...

Keep these replacement tips handy when wire pulling with fiberglass fish tapes. They are good to have around just in case anything unexpected happe...

The Replacement Leader is used with the Magnetic Wire Puller (Cat. No. 50611) from Klein Tools. The Leader consists of strong Rare-Earth magnets an...

The Whisk Attachment is a replacement part for the 7-Piece Fish Rod Attachment Set (Cat. No. 56511). The threaded female end allows the Whisk Attac...

The Chain Attachment is a replacement part for the 7-Piece Fish Rod Attachment Set (Cat. No. 56511). The Magnet (Cat. No. 56515) attaches to the Ch...

The Chain Attachment is a replacement part for the 7-Piece Fish Rod Attachment Set (Cat. No. 56511). The Magnet attaches to the Chain (Cat. No. 565...

The Twin Hook Attachment is a replacement part for the 7-Piece Fish Rod Attachment Set (Cat. No. 56511). This durable stainless steel grappling-sty...

The Bullet Nose and the Single Hook Attachment are replacement parts for the 7-Piece Fish Rod Attachment Set (Cat. No. 56511). These durable stainl...

Designed for optimal set-up and slug removal speed. For use in hydraulic drivers, punch and die are required for operation. Draw stud's flat end de...

For use in hydraulic drivers. Punch and die are required for operation. Draw stud's flat end designed to guide punch for faster thread engagement. ...

The 2.416-Inch Knockout Punch easily punches holes for 2-Inch conduit. It offers an optimized design that reduces wrench effort. Slugs are split in...

Easily punch holes for1-1/2-Inch EMT conduit. Has a maximum capacity of 10 gauge mild steel. Cuts aluminum, fiberglass and plastic as well. Optimiz...

Easily punch holes for 1-1/4-Inch EMT conduit. Has a maximum capacity of 10 gauge mild steel. The optimized design reduces wrench effort. Slugs are...

Easily punch holes for 1-Inch EMT conduit. Has a maximum capacity of 10 gauge mild steel. Cuts aluminum, fiberglass and plastic. The optimized desi...

Easily punch holes for 3/4-Inch EMT conduit. Has a maximum capacity of 10 gauge mild steel. Cuts aluminum, fiberglass and plastic. The optimized de...

The 7/8-Inch Knockout Punch easily punches holes for 1/2-Inch EMT conduit. The optimized design reduces wrench effort. Slugs are split inside for e...

Set includes 1'' (25 mm) ratcheting wrench, knockout punches, dies and draw studs for 1/2'' (13 mm), 3/4'' (19 mm), 1'' (25 mm), 1-1/4'' (32 mm), ...

This Punch Set can punch clean and accurate holes in electrical panels. The 1/2-Inch Knockout Punch 3-Piece set can cut up to 10-gauge mild steel. ...

This Punch Set can punch clean and accurate holes in electrical panels. The 3/4-Inch 3-piece set can punch up to 10-gauge mild steel. It can also c...

For use with Klein's Impact Punchdown Tool (VDV427-300), this replacement blade is used to punch data cables into 110 panels and blocks. Terminate ...

Dura-Blade™ 66/110 Cut Combination Punchdown Blade is designed for durability and performance. One blade terminates and cuts on both 66 and110 pane...

The Punchdown Tool Blade terminates 66-style cable connections in a variety of cross-connect panels, blocks and keystone jacks. The reversible blad...